• Fengfan Degreasing Wax Removal Agent Aluminum Anodizing Chemicals Phoenix Clean 151
  • Fengfan Degreasing Wax Removal Agent Aluminum Anodizing Chemicals Phoenix Clean 151

Fengfan Degreasing Wax Removal Agent Aluminum Anodizing Chemicals Phoenix Clean 151

A water-soluble powder that degreases and de-waxes aluminum extrusions, plate and polished parts in one weakly alkaline bath before anodizing.
  • Fengfan Degreasing Wax Removal Agent Aluminum Anodizing Chemicals Phoenix Clean 151

Description

Product Overview

Phoenix Clean 151 is a water-soluble powder that builds a weakly alkaline cleaning bath for aluminum parts on their way into aluminum anodizing. It is made for extruded profiles, plate, sheet and machined components that reach the line carrying drawing oils, machining oils, handling soils and, on polished work, the buffing wax left behind by mechanical polishing.

What distinguishes it is the combination. A dedicated dewaxing component works alongside the degreasing chemistry, so a polished part is cleaned and de-waxed in one tank instead of passing through a separate wax-removal stage before anodizing. The bath is only weakly alkaline, which keeps cleaning strength and aluminum compatibility in balance, and because the product is a powder, the same weight gives the same bath strength every time it is made up. That repeatability is what industrial metal plating and anodizing lines need when they are chasing a consistent finish rather than a single clean batch.

In the line, the bath sits in the pretreatment position: parts are cleaned, rinsed, then anodized. Wax and oil left on the surface are the usual reason an oxide layer comes out patchy, seals dull, or fails to hold colour on polished faces, which is why an aluminum anodizing service handling buffed extrusions watches this stage closely.

Key Features

  • Two jobs in one tank. Degreasing and dewaxing are built into the same powder, so the wax-removal stage that normally sits between polishing and anodizing can come out of the line.
  • Made for production, not one-off cleaning. The powder is formulated for industrial metal plating and anodizing lines that need the same result on the first part of a shift and on the last.
  • Fast on light oil. Parts carrying only machining or handling oil come clean in a short contact, so the bath keeps pace with the cycle time of a busy pretreatment line.
  • Heavy oil is covered too. Deep-drawn and profiled workpieces with thick drawing lubricant are handled by moving towards the stronger end of the concentration and time window rather than by changing product.
  • Removes polishing wax. The dedicated dewaxing additive lifts the compound left after buffing and mechanical polishing, which is the residue a plain alkaline degreaser leaves on the surface.
  • Weakly alkaline, not aggressive. Cleaning power is balanced against aluminum compatibility, so thin-walled and polished parts are not exposed to the attack that strongly caustic electroplating chemicals can cause on aluminum.
  • Drops into existing equipment. Air agitation, ultrasonics and circulation filtration are all suggested for this bath, so it fits lines already set up for those systems.
  • Cleaner surface into the anodizing aluminum process. Because oil and wax are gone before the part reaches the tank, the oxide layer forms evenly and holds its appearance through sealing.

Operating Parameters

ItemRangeRecommended condition
Bath concentration20 ~ 60 g/L45-55 g/L
pH7.5-12.08.5-11.0
Temperature50 ~ 70 °C55 ~ 65 °C
Time (about)3-30 min5-15 min
Air stirringSuggested useSuggested use
UltrasoundSuggested useSuggested use
Cycle filtrationSuggested useSuggested use

Use Scenarios

  • Extrusion lines before anodizing. Profiles racked straight from the saw or the polisher pass through this bath first; it takes off the drawing oil and handling soils that would otherwise show as streaks once the part is in the anodizing aluminum process.
  • Polished and buffed components. On buffed work the wax is the stubborn contaminant. Running it here removes wax and oil in the same contact, so an aluminum anodizing service does not need a second tank to heat, dose and maintain.
  • Job shops with mixed loads. A shop that handles light stamping oil one day and a heavy drawing lubricant the next covers both by adjusting concentration and contact time instead of switching products.
  • Complex geometry and blind holes. Where oil sits in recesses, ultrasonic cleaning or air agitation is suggested to keep fresh solution moving through the part.
  • High-volume lines with circulation filtration. Continuous filtration holds the bath uniform and pulls wax and oil out of the working volume, which is what keeps a large tank performing between make-ups.
  • Sites that also run metal plating services. Pretreatment discipline is the same whatever follows the rinse, so the bath fits a workshop that anodizes some work and plates other work on the same site.

Bath Make-Up & Line Integration

  1. Bring the water up to temperature first. Fill the tank and heat it before charging powder; warm water wets the particles so the powder dissolves instead of leaving lumps on the tank floor.
  2. Charge slowly under agitation. Add the powder at a steady rate with the agitator running, and keep it running until the solution is clear with no undissolved particles left in suspension.
  3. Set the strength to the workload. Lightly oiled extrusions run at the lower end of the concentration window; heavily oiled or heavily waxed parts need the upper end and a longer contact. Both windows are listed in the operating parameters above.
  4. Check pH before the first load. Adjust into the working range, then re-check after a few loads, because drag-in from polished parts shifts it faster than oil alone.
  5. Load with space between parts. Racked or basketed work with gaps between components cleans evenly; parts stacked against each other trap oil in the contact areas.
  6. Hold for the contact time the soil needs, then rinse thoroughly. A hard rinse between this bath and the tank an aluminum anodizing service runs is what stops cleaner carry-over from disturbing the anodizing bath.
  7. Keep filtration running through the shift. Circulation filtration is suggested to hold the concentration uniform and to take the wax and oil the bath has picked up out of the working volume — the same discipline metal plating services apply to their own pretreatment tanks.

Powder Handling & Storage

Treat the powder the way you would any other powdered chemical used in industrial metal plating: keep the container closed between uses, store it in a cool, dry place, and weigh out only what a make-up needs. Powder that has taken up moisture dissolves slowly and can leave undissolved specks in the bath, so close the liner after each charge and keep the container off a damp floor.

Working solutions perform most reliably when they are kept at temperature and under filtration through the shift rather than left standing cold with oil and wax in them. Label the tank clearly, and store the powder away from acids and from the electroplating chemicals kept in the same store room so that nothing is decanted into the wrong container. Operators should follow the handling precautions on the product documentation supplied with the material; gloves, eye protection and ventilation around a hot alkaline bath are standard practice.

Ordering & Delivery

ItemDetail
Minimum order quantityVaries by chemical; confirmed with our sales team per order
Payment100% T/T in advance
Lead time2 weeks
Packing10 kg/box; 25 kg or 50 kg/bag; 20 kg/25 kg/30 kg/200 kg/drum; 1000 kg/IBC drum
ShippingPer the terms agreed in the current contract
Documentation and warrantyInspection certificate issued after delivery stating the batch number and warranty period

Technical Support & Model Matching

Choosing the right match is where most sourcing decisions stall. As a trading supplier, we keep one point of contact from first enquiry to after-sales: tell us what you are making and the conditions you work under, and we shortlist the closest matches from our supplier network, compare specifications and arrange samples before you commit to a bulk order. If something does not behave as expected, we work with the supplying partner on the cause and a practical fix, and stay with the case until it is settled. Email, WeChat or WhatsApp enquiries get a reply within 24 hours.

FAQ

What is the optimal operating temperature for the bath before aluminum anodizing?

The bath runs from 50 °C to 70 °C and performs optimally between 55 °C and 65 °C. Inside that band both the alkaline action and the dewaxing additive work at a useful rate; below it, wax removal slows and contact times stretch out, and above it you are heating a tank that is already cleaning well. Hold the temperature steady through the shift rather than letting it drift between loads.

Can air agitation and circulation filtration be used at the same time?

Yes — both are suggested for this product. Air agitation keeps fresh solution against the part surface and stops oil from settling back onto the work, while circulation filtration holds the concentration even through the tank and removes the wax and oil the bath has taken up. On a line where the anodizing aluminum process has to repeat part after part, that stability between make-ups is what protects the finish. Ultrasonic cleaning can be used on the same basis where geometry traps soil.

Which oils and residues does it remove from aluminum parts?

The range a finishing shop actually sees: light machining and handling oils, heavier drawing lubricants on profiled or deep-drawn components, and the polishing wax left after buffing. Degreasing and dewaxing happen in the same contact, which is useful where a workshop also runs metal plating services and pretreats mixed work through one line.

How is the product formulated for environmental compliance?

It is a water-soluble powder that builds a weakly alkaline bath, designed around green product standards rather than a solvent-heavy liquid cleaner. That keeps the chemical residue carried into the rinse water lower and makes the waste stream simpler to handle. For the documentation your market asks for, speak to our sales contact and we will confirm what is available for your destination.

Is this a plating chemical itself, or only a pretreatment product?

It is a pretreatment product — it cleans the aluminum, it does not deposit a coating. It is supplied alongside the electroplating chemicals in our range because it belongs to the same sequence in the line: what the clean leaves behind decides what the anodizing or plating step can achieve.

Does it suit both extruded profiles and polished plate?

Yes. Sections, plate, sheet and machined parts are all handled. Polished work is where the dewaxing component earns its place, because buffing compound is exactly the residue a plain degreaser leaves behind. Match concentration and contact time to how heavily the part is oiled or waxed.

How do I know when the bath needs strengthening?

Watch the parts rather than the clock. If a wax film or a water-break shows on the surface after rinsing, move up within the concentration and time window, and check pH before blaming the powder — drag-in from polished work usually shifts it first. Regular filtration keeps the working life predictable.

REQUEST MORE DETAILS

Please fill out the form below and click the button to request more information about
Name
Email *
Message
Verification Code *
Click to verify
Leave a message
Name
Email *
Message
Verification Code *
Click to verify